 |
|---|
Just working this out. You don't take it out fully. That doesn't matter. You can push it back on. You are just putting it out by about that much. So in here. You have one there. Prior it out. And place one in there. You see it's obvious where they go. Look. If it comes in a bit awkward. You just get them in. There they are sitting like that. You then pull back. Like that. And it's reverse now. You ok with this you think? It's pretty straight forward. It will be a bit tricky, a little bit fiddly. But you're in no rush. All you are doing is. It's a bit tricky. All you are doing is giving it a little. Sometimes they go straight on. Sometimes they don't. Sorry. Sometimes they go straight on. All you are doing is Pushing it over. Until it meets the little groove. You can feel it clicking. You will be able to. With that. Like move them around. So you know it's in place. That's it done. All you are doing is lapping it back on. That's it. It has a free run. There's a different strengths. And what's in our little box. You will have a cap that meets mirror image on it. Right. And you do the same again. Put it all back so. So it's even going to look like that. Or it will look like this, look. The cap. Them caps match. Oh, and it would be nice. Get them all matching but they might not do. If you are a bit unsure. It don't matter. Wait until I come back.
.....a roof, I need to put glasses on. You get your circular pin. Prise it off. Drop it down there. Sometimes they will spring. Just working this out. All you are doing is this comes out. You don't take it out fully. That doesn't matter. You can push it back on. You are just putting it out by about that much. So in here. You have one there. And you just use your screwdriver. Here's the screwdriver. Prior it out. They are all too compressed and broken.You get two new rubbers. And place one in there. You see it's obvious where they go. Look. They have got like a little cup they sit in. If it comes in a bit awkward. You just get them in. There they are sitting like that. You then pull back. Like that. And it's reverse now. You now get your Circlip. You ok with this you think? It's pretty straight forward. Although you are videoing it. It will be a bit tricky, a little bit fiddly. But you're in no rush. Once you have done a couple. The middle one. I do this one first and then I will show you. All you are doing is. With your thumb. It's a bit tricky. All you are doing is giving it a little. Sometimes they go straight on. Sometimes they don't, sorry. Sometimes they go straight on. All you are doing is Pushing it over. Until it meets the little groove. You can feel it clicking. And also you get your Circlip pliers. You will be able to. With that. Like move the Circlip around. So you know it's in place. That's it done.Then put your cap back on. Which you might replace. All you are doing is lapping it back on. That's it. Now you are getting. Your nut and washer. Make sure you keep all three of them together. Just going to do it back up. Yeah you can do it tight. It has a free run as it has ball bearing. That is a separate piece of metal here. You are just tightening, right. So it doesn't come off. I mean it's as tight as you think. You know what I mean. There's a different strengths. So cap goes back on.So, so this side hasn't got any cover on it.So I'll just have a look to see what that's got. I'd undo that nut to see what's underneath there. And what's in our little box. You will have a cap that meets mirror image on it. Right. And you do the same again. Put it all back so. So it's even going to look like that. Or it will look like this, look. You come around this side. The cap. Them caps match. Oh, and it would be nice. Get them all matching but they might not do. But as long as they have got a cap on it. And a nut and bolt. If you are a bit unsure. It don't matter. Wait 'till I come back.